Possible solutions: The above leads me to believe that the Syno is blocking access somehow. I've also tried logging in as either "root" and "rsync" (both paired with the admin password) with the various host options mentioned - all failed. I've ensured that the "Network Backup Destination" and "Network Backup Volume" services in Control Panel > Info > Service are enabled. I've confirmed that the "Enable Network Backup Service" and "Use customized rsync configuration" checkboxes in Backup & Replication > Backup Services are checked. Solutions tried: I've used the following host options (where "IP" is the whole prefix): IP:22, IP:873, IP:6281 (ports taken from here). Note: the above settings were the settings used on the CS and worked perfectly. Unfortunately, ReadyNAS doesn't give details on the error. When I click "Test Connection", I get the following: "Error connecting to 192.168.2.10". The problem is that I can't get the ReadyNAS to connect to the Syno. photos, videos, music, etc.) to the appropriate top-level share. THEN I can have the Syno automatically move the subfolders (e.g. If I want to back up my 'media' folder on my ReadyNAS to the Syno, I have to create the following folder: volume1/NetBackup/media. Sidenote: as far as I understand rsync backs up the data to the volume1/NetBackup share only - i.e. In Step 2 of the documentation above, I have to specify the backup destination. Now, I had rsync set up on the CS but maybe I'm missing something when I upgraded to DSM 3.2 to 5.2. Instructions for setting up rsync on the ReadyNAS are here so we're all on the same page. I'm trying to keep the ReadyNas as the primary appliance where I dump videos and have it rsync to the Syno where I can then do other stuff with it (as the Syno is more "up to date", so to speak).īut I've hit the most infuriating block with rsync. So I decided to put the CS407e remote backup issue on the backburner for now as I complete setup of the DS411j. Would prefer to stick with rsync than go with NFS (which I can connect to). I suspect a host address failure but not sure how to check. (You don’t need to specify the -progress option in order to use -info=progress2.TL DR: ReadyNAS cannot connect to Syno. avoid -v or specify -info=name0) if you want to see how the transfer is doing without scrolling the screen with a lot of names. Use this flag without outputting a filename (e.g. There is also a -info=progress2 option that outputs statistics based on the whole transfer, rather than individual files. then press / key and type progress2 press Enter to search for it press n for the 'n'ext match until you find the entry you're looking for: You'll now have access to the -info=progress2 option: man rsync This is free software, and youĪre welcome to redistribute it under certain conditions. Socketpairs, hardlinks, symlinks, IPv6, batchfiles, inplace,Īppend, no ACLs, xattrs, iconv, symtimes, prealloc rsync -versionĬopyright (C) 1996-2018 by Andrew Tridgell, Wayne Davison, and others.Ħ4-bit files, 64-bit inums, 64-bit timestamps, 64-bit long ints, Make note of this so you can see later it actually got updated. Ultimately you just need to be cded into this extracted directory containing the rsync source code.Ĭheck current version of rsync. Right-click the screen in your folder manager and go to "Open in Terminal." Alternatively, do steps 2 through 4 manually on the command line. In your folder explorer, right-click it and go to "Extract Here".Įnter the extracted folder (ex: "rsync-3.1.3") Save it in a directory WITH NO SPACES AT ALL to ensure it builds right. But, what do I do if my version of rsync is too old and doesn't support this option? Answer: upgrade rsync! Here's how to build rsync from source on Ubuntuĭownload latest version of rsync. Yeah, do what Jon said: use the -info=progress2 option. Note that when the transfer starts the total number of chunks, and therefore the current progress, can change when the recursive option is used as more files are discovered for syncing So the following: rsync -r -info=progress2 -info=name0 "$src" "$dst" If you want to see how the transfer is doing without scrolling the screen The whole transfer, rather than individual files. There is also a -info=progress2 option that outputs statistics based on Make it much easier to specify these two options for a long transfer that The explanation of how to use it comes under the -P option in the man page: -P The -P option is equivalent to -partial -progress. Rsync has a -info option that can be used to not only output the current progress, but also the transfer rate and elapsed time: -info=FLAGS fine-grained informational verbosity
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |